New Creader CR3001 x431 OBD2 Scanner, Engine Fault Code Reader Diagnostic Scan Tool
for All OBDII Protocol Cars
Top 5 Reasons to Get Launch Creader 3001:
1.Accureate Quick Diagnosis Tool
2.Full Funciton OBD Scanner
3.Wide Compatibility
4.Powerful Scan Tool
5.100% Risk Free Purche
(Note: CR3001 only Support 12V Gasoline& Diesel, Does not support 24V Truck )
CR3001 supports to remove engine lights, and the below parts might cause your check engine light on:
1. Gas Cap.
2. Oxygen Sensor.
3. Air Fuel Ratio Sensor.
4. Mass Air Flow Sensor.
5. Ignition Coils.
6. Spark Plug Wires.
7. Spark Plugs.
8. Thermostat.
9. EGR Valve.
10. Evaporatative Emission Canister Purge Valve(EVAP).
11. Catalytic Converter.
LAUNCH CR3001 Top 10 Powerful Full OBD2 Functions
1. Reading Codes: Show the detailed description of the Diagnostic Trouble Code (DTCs).
2. Erasing Codes & Reset: Turn off Check Engine Light(MIL), clear codes and reset monitors.
3. Data Stream: Read and display live ECU/PCM data stream, plotting functions graphically and stores freeze frame data.
4. I/M Readiness Status: Show whether the various emissions-related systems on the vehicle are operating properly and are ready for inspection and maintenance testing.
5. Read Live Data Stream: Show the information of continuous data stream from a vehicle in live graphic(waveform) display.
6. View Freeze Frame Data: Check the certain vehicle conditions which are recorded by the on-board computer at the time the emission-related fault occurs.
7. O2 Sensor Test: Allow retrieval and viewing of O2 sensor monitor test results for the most recently performed tests from the vehicle's on-board computer.
8. On-Board Monitor Test: Retrieve and displays test results for emission-related powertrain components and systems.
9. Read Vehicle Information: Display the information such as VIN (Vehicle Identification Number), CID (Calibration ID) and CVN (Calibration verification number), etc.
10. Component Test: Certain vehicle components can be actuated by commands sent from the scanner to test their operability.
Creader 3001 supports 10 modes of OBDII diagnostic :
Mode $01 Request current powertrain diagnostic data.
Mode $02—Request freeze frame information.
Mode $03—Request emissions-related diagnostic troublecodes.
Mode $04—Clear/reset emissions-related diagnosticinformation.
Mode $05—Request oxygen sensor monitoring test results.
Mode $06—Request on-board monitoring test results for specific monitored systems.
Mode $07 — Request emission-related diagnostic troublecodes detected during current or last completed drivingcycle
Mode $08—Request control of on-board system, test orcomponent.
Mode $09—Request vehicle information.
Mode $0A—Request emissions-related diagnostic troublecodes with permanent status after a clear/reset emission-related diagnostic information service.
Launch Creader 3001 Support Languages:
Multi-Language: English , French , Russian , Spanish ,German, Italian ,Portuguese
American cars: Standard OBD2 protocols since 2000, include Chrysler, Ford, GM......
European cars: Standard OBD2 protocols since 2003, include VW, Opel, Audi, Seat, Peugeot, Renault, BMW, Volvo....
Japanese/Korean cars: Standard OBD2 protocols since 2006, include KIA, Isuzu, Mitsubishi, Hyundai, Mazda, Nissan, Toyota...
Chinese cars: Standard OBD2 protocols since 2009.
Russian cars: Standard OBD2 protocols since 2012, include GAZ, VAZ, LADA, IZH, PAZ, SeAZ, UAZ, ZAZ...
Package
1*CR3001 Code Reader
1*USB Cable
1*User Manual
for All OBDII Protocol Cars
Top 5 Reasons to Get Launch Creader 3001:
1.Accureate Quick Diagnosis Tool
2.Full Funciton OBD Scanner
3.Wide Compatibility
4.Powerful Scan Tool
5.100% Risk Free Purche
(Note: CR3001 only Support 12V Gasoline& Diesel, Does not support 24V Truck )
CR3001 supports to remove engine lights, and the below parts might cause your check engine light on:
1. Gas Cap.
2. Oxygen Sensor.
3. Air Fuel Ratio Sensor.
4. Mass Air Flow Sensor.
5. Ignition Coils.
6. Spark Plug Wires.
7. Spark Plugs.
8. Thermostat.
9. EGR Valve.
10. Evaporatative Emission Canister Purge Valve(EVAP).
11. Catalytic Converter.
LAUNCH CR3001 Top 10 Powerful Full OBD2 Functions
1. Reading Codes: Show the detailed description of the Diagnostic Trouble Code (DTCs).
2. Erasing Codes & Reset: Turn off Check Engine Light(MIL), clear codes and reset monitors.
3. Data Stream: Read and display live ECU/PCM data stream, plotting functions graphically and stores freeze frame data.
4. I/M Readiness Status: Show whether the various emissions-related systems on the vehicle are operating properly and are ready for inspection and maintenance testing.
5. Read Live Data Stream: Show the information of continuous data stream from a vehicle in live graphic(waveform) display.
6. View Freeze Frame Data: Check the certain vehicle conditions which are recorded by the on-board computer at the time the emission-related fault occurs.
7. O2 Sensor Test: Allow retrieval and viewing of O2 sensor monitor test results for the most recently performed tests from the vehicle's on-board computer.
8. On-Board Monitor Test: Retrieve and displays test results for emission-related powertrain components and systems.
9. Read Vehicle Information: Display the information such as VIN (Vehicle Identification Number), CID (Calibration ID) and CVN (Calibration verification number), etc.
10. Component Test: Certain vehicle components can be actuated by commands sent from the scanner to test their operability.
Creader 3001 supports 10 modes of OBDII diagnostic :
Mode $01 Request current powertrain diagnostic data.
Mode $02—Request freeze frame information.
Mode $03—Request emissions-related diagnostic troublecodes.
Mode $04—Clear/reset emissions-related diagnosticinformation.
Mode $05—Request oxygen sensor monitoring test results.
Mode $06—Request on-board monitoring test results for specific monitored systems.
Mode $07 — Request emission-related diagnostic troublecodes detected during current or last completed drivingcycle
Mode $08—Request control of on-board system, test orcomponent.
Mode $09—Request vehicle information.
Mode $0A—Request emissions-related diagnostic troublecodes with permanent status after a clear/reset emission-related diagnostic information service.
Launch Creader 3001 Support Languages:
Multi-Language: English , French , Russian , Spanish ,German, Italian ,Portuguese
American cars: Standard OBD2 protocols since 2000, include Chrysler, Ford, GM......
European cars: Standard OBD2 protocols since 2003, include VW, Opel, Audi, Seat, Peugeot, Renault, BMW, Volvo....
Japanese/Korean cars: Standard OBD2 protocols since 2006, include KIA, Isuzu, Mitsubishi, Hyundai, Mazda, Nissan, Toyota...
Chinese cars: Standard OBD2 protocols since 2009.
Russian cars: Standard OBD2 protocols since 2012, include GAZ, VAZ, LADA, IZH, PAZ, SeAZ, UAZ, ZAZ...
Package
1*CR3001 Code Reader
1*USB Cable
1*User Manual